How to Set up a Bathtub Yourself
How to Set up a Bathtub Yourself
Blog Article
On this page in the next paragraph you can discover a good deal of good quality help and advice related to How to Install a Bathtub.
Setting up a tub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably hard job. If the old tub is conveniently obtainable, the job can move speedily; if you need to open a wall to get rid of the old bathtub and place the brand-new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Ensure you have certified on your own for the task and are comfortable trying it. As opposed to employing a professional to take over a halfway-completed task, it is far better to think about employing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly help you mount a new bathtub in your shower room if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous water system pipes.
Your devices and product checklist must comprise the following:
Getting ready for the Installation
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic because of the limited accessibility that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. When the supply pipes have been eliminated, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before moving on to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, position the bath tub in the needed placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub until the spirit level reads level.
To mount faucets, fit the bottom of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; after that do the exact same for the other faucet.
Activate the water system as well as check all joints as well as new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as additionally inspect the overflow outlet and also the regular outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as securing around the tub should wait up until the bathtub has actually been used at the very least once as this will certainly resolve it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the tap ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall in between the bathroom and the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, and are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the tub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily offered on the marketplace. It is suggested to fit the floor tiles using waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our piece on Installing A Bathtub. Thanks for taking a few minutes to browse our piece of content. Enjoyed reading our blog? Please share it. Let another person check it out. Thanks for your time spent reading it.
Booking Page
Report this page